911uk

Brake pipes

Add to repair workspace

New repair projectOpen repair workspace

Original source

2 captured repliesDiscussion pagination complete · Source accounts, not a confirmed diagnosis

THIS DISCUSSION / SOURCE-DERIVED OVERVIEW

Discussion summary

YOUR RESEARCHBrake pipes

Leading reported evidence

Replace front one

Suggestion or failed attempt

No successful repair reported for this finding.

0
Reported fixes: 0
Unsuccessful attempts: 1
Discussions

Read evidence and context

Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.

Discussions that contain suggestions: 1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Suggestion · Original poster
Has any one changed the front one that goes from the drivers side to the n/s inner wing, I can just about see it, I might be able to get to it if I drop the anti roll bar , but even then it will be very tight, I can get a new pipe through a new route , but I will not be able to get in there to secure it, getting the bolts undone on the anti roll bar looks like a another snap off and drilling and re tapping job , just like a lot of others on this car.
Original post Read captured discussion
Brake pipes

Read full discussion summary

Leading evidence: 'Replace front one' (no explicit attributable resolution; this is a reported action or suggestion). Across 1 matching discussions, The most frequently discussed action is 'Replace front one' (1 discussions). For that action, 0 discussions report a resolution and 0 report an unsuccessful attempt. No action has an explicit, attributable resolution report under the current rules. These are forum reports and suggestions, not a confirmed diagnosis.

Source reports, not a diagnosis or a success probability. Counts refer to discussions and can overlap.

Read captured replies

1 matching discussions · 2 captured posts examined · 0 partial discussions

Compare 1 other evidence results

Replace pipes including hoses all the way up

Suggestion or failed attempt

No successful repair reported for this finding.

0
Reported fixes: 0
Unsuccessful attempts: 1
Discussions

Read evidence and context

Discussions that contain suggestions: 1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Suggestion · Original poster
My 911 c2 3.4 tiptronic, 1998 I have quite a few jobs to do on this car, fuel rails on another thread, a nightmare, but this all stated because of rusty brake pipes, And I had to take the engine out to get to them, I have now manage to replace all the pipes including hoses all the way up to the front n/s inner wing.
Original post Read captured discussion
Brake pipes

Frequently discussed actions (2)

These are separate views of the same evidence. Frequency alone does not establish a fix, and these counts must not be added together.

Replace front one

No successful repair reported for this finding.

0
Reported fixes: 0
Unsuccessful attempts: 1
Discussions

Read evidence and context

Discussions that contain suggestions: 1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Suggestion · Original poster
Has any one changed the front one that goes from the drivers side to the n/s inner wing, I can just about see it, I might be able to get to it if I drop the anti roll bar , but even then it will be very tight, I can get a new pipe through a new route , but I will not be able to get in there to secure it, getting the bolts undone on the anti roll bar looks like a another snap off and drilling and re tapping job , just like a lot of others on this car.
Original post Read captured discussion
Brake pipes

Replace pipes including hoses all the way up

No successful repair reported for this finding.

0
Reported fixes: 0
Unsuccessful attempts: 1
Discussions

Read evidence and context

Discussions that contain suggestions: 1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Suggestion · Original poster
My 911 c2 3.4 tiptronic, 1998 I have quite a few jobs to do on this car, fuel rails on another thread, a nightmare, but this all stated because of rusty brake pipes, And I had to take the engine out to get to them, I have now manage to replace all the pipes including hoses all the way up to the front n/s inner wing.
Original post Read captured discussion
Brake pipes

Coverage and how to read this overview

Counts describe captured discussions, not unique people or a diagnosis. Author identities are not reliably stored. Exact duplicate evidence is counted once across matching discussions; one discussion counts at most once per action/state. Multiple repairs reported together remain a combination. Suggestions and failed attempts do not establish a fix. Matches cover whole discussions and can include related faults, model variants and incomplete threads.

2 eligible posts · 0 unverified posts · 1 discussions match the subject in their title or opening post.

911uk: 1 discussions

0 evidence records excluded for query context · 0 excluded by outcome qualification · 0 adjusted by outcome qualification.

0 acknowledgements have no verified action link; they do not establish a repair result.

Generation: 20261027T035758Z · outcome-qualification-6. Deterministic extraction; no AI model inference. How we use sources

POST 1 / ORIGINAL POSTEROriginal post

My 911 c2 3.4 tiptronic, 1998 I have quite a few jobs to do on this car, fuel rails on another thread, a nightmare, but this all stated because of rusty brake pipes, And I had to take the engine out to get to them, I have now manage to replace all the pipes including hoses all the way up to the front n/s inner wing. Has any one changed the front one that goes from the drivers side to the n/s inner wing, I can just about see it, I might be able to get to it if I drop the anti roll bar , but even then it will be very tight, I can get a new pipe through a new route , but I will not be able to get in there to secure it, getting the bolts undone on the anti roll bar looks like a another snap off and drilling and re tapping job , just like a lot of others on this car. Paul

POST 2Original post

I've done mine - dropped the subframe / propped up the fuel tank. Worth checking the steering rack external steel pipes - a company in Borsall Common makes them for £50 ish. Porsche will only fit a new rack. Search the forum - I've posted on the subject previously.

This is a source reference. Confirm exact model applicability in the original material.