6 captured repliesDiscussion pagination complete · Source accounts, not a confirmed diagnosis
THIS DISCUSSION / SOURCE-DERIVED OVERVIEW
Discussion summary
YOUR RESEARCHChanging the clutch
Leading reported evidence
Adjust pressure screw so
Suggestion or failed attempt
No successful repair reported for this finding.
0
Reported fixes
0
Unsuccessful attempts
1
Discussions
Read evidence and context
Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.
Discussions that contain suggestions
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Suggestion
Assemble special tool retaining device 9624/1 on the body with the anti-roll bar fastening screws and adjust pressure screw so that the pressure disc is aligned with the crankcase.
Leading evidence: 'Adjust pressure screw so' (no explicit attributable resolution; this is a reported action or suggestion). Across 1 matching discussions, The most frequently discussed action is 'Adjust pressure screw so' (1 discussions). For that action, 0 discussions report a resolution and 0 report an unsuccessful attempt. No action has an explicit, attributable resolution report under the current rules. These are forum reports and suggestions, not a confirmed diagnosis.
Source reports, not a diagnosis or a success probability. Counts refer to discussions and can overlap.
These are separate views of the same evidence. Frequency alone does not establish a fix, and these counts must not be added together.
Adjust pressure screw so
No successful repair reported for this finding.
0
Reported fixes
0
Unsuccessful attempts
1
Discussions
Read evidence and context
Discussions that contain suggestions
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Suggestion
Assemble special tool retaining device 9624/1 on the body with the anti-roll bar fastening screws and adjust pressure screw so that the pressure disc is aligned with the crankcase.
Counts describe captured discussions, not unique people or a diagnosis. Author identities are not reliably stored. Exact duplicate evidence is counted once across matching discussions; one discussion counts at most once per action/state. Multiple repairs reported together remain a combination. Suggestions and failed attempts do not establish a fix. Matches cover whole discussions and can include related faults, model variants and incomplete threads.
6 eligible posts · 0 unverified posts · 1 discussions match the subject in their title or opening post.
Porsche Club GB: 1 discussions
0 evidence records excluded for query context · 0 excluded by outcome qualification · 0 adjusted by outcome qualification.
0 acknowledgements have no verified action link; they do not establish a repair result.
Generation: 20261026T124918Z · outcome-qualification-6. Deterministic extraction; no AI model inference. How we use sources
Hi guys how easy is it to do and is it possible for me to diy it? I notice the kit seems to be around £250ish and porschtek say it will be 400 labour is that about right?
Depends how handy you are. Book time is about 4 hours, so around £220-250 labour at an indy.
Here's a couple of extracts from the manual:
Remove transmission:
1. Remove underbody panels (middle and rear).
2. Remove cross member.
3. Support engine with special tool retaining device 9624/1 . To do so, remove the anti-roll bar mount and pivot anti-roll bar forwards.
4. Assemble special tool retaining device 9624/1 on the body with the anti-roll bar fastening screws and adjust pressure screw so that the pressure disc is aligned with the crankcase.
Note
Protect drive shafts against damage, e.g. with hose (30 mm diameter)
5. Remove drive shaft on transmission side.
6. Separate electrical connection from the back-up light switch.
7. Unclip the hydraulic line for the clutch slave cylinder at the side transmission case cover.
8. Unscrew clutch slave cylinder and suspend on side. Do not remove hydraulic line.
Note: The clutch pedal must not be pressed if the clutch slave cylinder has been removed. Danger of injury from the push rod which can be pressed out of the slave cylinder hydraulically. Affix a warning note in the vehicle!
9. Remove switch cable from the transmission and pull it off the transmission switch and selector lever.
10. Place transmission jack under the transmission and fasten fixing strap.
11. Remove gear support.
12. Remove transmission bracket.
Note: The transmission can be lowered by a maximum of 25 mm to improve accessibility.
13. Unscrew fastening screws (8) between engine and transmission.
14. Pull transmission to the front and lower it.
Remove cluch:
1. Remove manual transmission.
2. Fasten toothed segment (special tool 9538/1) on the crankcase half (cylinder bank 1 - 3) with hexagon-head bolt M12 x 50.
3. Detach thrust plate.
Note: In order to avoid deformation of the thrust plate housing, always loosen screws in several stages and in diametrically opposite sequence.
4. Remove thrust plate and drive plate.
If you would like a copy of the pages, drop me an email.
9624/1 is to support the engine while you remove the transmission, as it is normally supported by the transmission mount at that end. 9538/1 is a toothed piece which locks up the flywheel, so you can undo the pressure plate bolts easily without the flywheel rotating. Depends if you are good at improvisation as to whether you need them or not.
This is a source reference. Confirm exact model applicability in the original material.
