10 captured repliesDiscussion pagination complete · Source accounts, not a confirmed diagnosis
THIS DISCUSSION / SOURCE-DERIVED OVERVIEW
Discussion summary
YOUR RESEARCHPutting it on jackstands
Leading reported evidence
Replace inner track rod ends i put it up
Suggestion or failed attempt
No successful repair reported for this finding.
0
Reported fixes
0
Unsuccessful attempts
1
Discussions
Read evidence and context
Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.
Discussions that contain suggestions
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Suggestion · Original poster
During my failed attempt at replacing the inner track rod ends I put it up on jackstands using the factory jacking points.
Leading evidence: 'Replace inner track rod ends i put it up' (no explicit attributable resolution; this is a reported action or suggestion). Across 1 matching discussions, The most frequently discussed action is 'Replace inner track rod ends i put it up' (1 discussions). For that action, 0 discussions report a resolution and 0 report an unsuccessful attempt. No action has an explicit, attributable resolution report under the current rules. These are forum reports and suggestions, not a confirmed diagnosis.
Source reports, not a diagnosis or a success probability. Counts refer to discussions and can overlap.
Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.
Discussions that contain suggestions
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Suggestion · Original poster
My question after all that is would it be safe to use the axle stands on the reinforced part if you used hockey pucks?
Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.
Discussions that contain suggestions
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Suggestion · Original poster
During my failed attempt at replacing the inner track rod ends I put it up on jackstands using the factory jacking points.
Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.
Discussions that contain suggestions
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Suggestion · Original poster
My question after all that is would it be safe to use the axle stands on the reinforced part if you used hockey pucks?
Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.
Discussions that contain suggestions
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Suggestion · Original poster
Use the subframe OK at the back but the front with all the plastic covers it's its a more tricky to see where to put the axle stands.
Counts describe captured discussions, not unique people or a diagnosis. Author identities are not reliably stored. Exact duplicate evidence is counted once across matching discussions; one discussion counts at most once per action/state. Multiple repairs reported together remain a combination. Suggestions and failed attempts do not establish a fix. Matches cover whole discussions and can include related faults, model variants and incomplete threads.
10 eligible posts · 0 unverified posts · 1 discussions match the subject in their title or opening post.
911uk: 1 discussions
0 evidence records excluded for query context · 0 excluded by outcome qualification · 0 adjusted by outcome qualification.
0 acknowledgements have no verified action link; they do not establish a repair result.
Generation: 20261026T220748Z · outcome-qualification-6. Deterministic extraction; no AI model inference. How we use sources
Hi all. During my failed attempt at replacing the inner track rod ends I put it up on jackstands using the factory jacking points. This was a fath as I jacked it from the suggested reinforced point as suggested in 101 projects book.
This meant jack onesies to get it high enough for my really big jack on the otherside taking the wheel off with it dangling in the air to give room to get it under enough the getting it high enough for the stand to go under then repeating on the otherside. When I came to lower the car I couldn't get a wheel on and my jack in so took a third jack to eventually get it down again.
My question after all that is would it be safe to use the axle stands on the reinforced part if you used hockey pucks? Or is there a risk this part won't be strong enough and has anyone tried it? I've included the picture so you know which part I'm talking about.
Thanks Alex. Is there a specific point on the front subframe you use at all? Use the subframe OK at the back but the front with all the plastic covers it's its a more tricky to see where to put the axle stands.
I hate putting my car up on jack stands due to the rocking back and forth thing. Why I finally ended up with QuickJacks. Before these one technique I used was to jack from the rear jackpoint and put stands under front jackpoint location and rear under the large crossmember knuckle (where control arm attaches). Stable and less back and forth.
Had a look tonight and can see the points but need to get the undertray off first so stumped myself with that one as don't want to get under until it's got the stands under.
This is a source reference. Confirm exact model applicability in the original material.
