20 captured repliesPartial discussion capture · Source accounts, not a confirmed diagnosis
THIS DISCUSSION / SOURCE-DERIVED OVERVIEW
Discussion summary
YOUR RESEARCHJack Stand Usage - 986 Forum - The Community for Porsche Boxster & Cayman Owners
Leading reported evidence
Use esco stands
Performed · outcome unconfirmed
No successful repair reported for this finding.
0
Reported fixes
0
Unsuccessful attempts
1
Discussions
Read evidence and context
Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.
Discussions that performed work without a confirmed outcome
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Performed · outcome unconfirmed
I use Esco stands that have a rubber pad built in.
Jack Stand Usage - 986 Forum - The Community for Porsche Boxster & Cayman Owners
Read full discussion summary
Leading evidence: 'Use esco stands' (no explicit attributable resolution; this is a reported action or suggestion). Across 1 matching discussions, The most frequently discussed action is 'Use esco stands' (1 discussions). For that action, 0 discussions report a resolution and 0 report an unsuccessful attempt. No action has an explicit, attributable resolution report under the current rules. These are forum reports and suggestions, not a confirmed diagnosis.
Source reports, not a diagnosis or a success probability. Counts refer to discussions and can overlap.
Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.
Discussions that performed work without a confirmed outcome
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Performed · outcome unconfirmed
I use a floor jack on the back end and it lifts the car enough to put the jack stands on the front end.
Jack Stand Usage - 986 Forum - The Community for Porsche Boxster & Cayman Owners
Use rubber
Performed · outcome unconfirmed
No successful repair reported for this finding.
0
Reported fixes
0
Unsuccessful attempts
1
Discussions
Read evidence and context
Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.
Discussions that performed work without a confirmed outcome
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Jack Stand Usage - 986 Forum - The Community for Porsche Boxster & Cayman Owners
Use good and sturdy stands, i also am
Suggestion or failed attempt
No successful repair reported for this finding.
0
Reported fixes
0
Unsuccessful attempts
1
Discussions
Read evidence and context
Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.
Discussions that contain suggestions
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Suggestion
You can actually from either spot lift the entire side of the car and place jack stands on the standard point on front and rear and then move to the other side and do the same thing, I have been doing it this way for the last 7 years with never an issue, just make sure you are placing a hockey puck pad on jack and using good and sturdy stands, I also am using the insert on stands that fits into the hole at the standard jacking point.
Jack Stand Usage - 986 Forum - The Community for Porsche Boxster & Cayman Owners
Use hockey puck
Suggestion or failed attempt
No successful repair reported for this finding.
0
Reported fixes
0
Unsuccessful attempts
1
Discussions
Read evidence and context
Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.
Discussions that contain suggestions
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Jack Stand Usage - 986 Forum - The Community for Porsche Boxster & Cayman Owners
Use good and sturdy stands, i also am
No successful repair reported for this finding.
0
Reported fixes
0
Unsuccessful attempts
1
Discussions
Read evidence and context
Discussions that contain suggestions
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Suggestion
You can actually from either spot lift the entire side of the car and place jack stands on the standard point on front and rear and then move to the other side and do the same thing, I have been doing it this way for the last 7 years with never an issue, just make sure you are placing a hockey puck pad on jack and using good and sturdy stands, I also am using the insert on stands that fits into the hole at the standard jacking point.
Jack Stand Usage - 986 Forum - The Community for Porsche Boxster & Cayman Owners
Use insert
No successful repair reported for this finding.
0
Reported fixes
0
Unsuccessful attempts
1
Discussions
Read evidence and context
Discussions that contain suggestions
1
0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.
0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.
Suggestion
You can actually from either spot lift the entire side of the car and place jack stands on the standard point on front and rear and then move to the other side and do the same thing, I have been doing it this way for the last 7 years with never an issue, just make sure you are placing a hockey puck pad on jack and using good and sturdy stands, I also am using the insert on stands that fits into the hole at the standard jacking point.
Jack Stand Usage - 986 Forum - The Community for Porsche Boxster & Cayman Owners
Coverage and how to read this overview
Counts describe captured discussions, not unique people or a diagnosis. Author identities are not reliably stored. Exact duplicate evidence is counted once across matching discussions; one discussion counts at most once per action/state. Multiple repairs reported together remain a combination. Suggestions and failed attempts do not establish a fix. Matches cover whole discussions and can include related faults, model variants and incomplete threads.
20 eligible posts · 0 unverified posts · 1 discussions match the subject in their title or opening post.
986Forum: 1 discussions
0 evidence records excluded for query context · 0 excluded by outcome qualification · 0 adjusted by outcome qualification.
1 acknowledgements have no verified action link; they do not establish a repair result.
Outcome without a verified action link
It has worked very well for me for a number of years.
I want to jack up the front of the Box and put it on jack stands. Here's my question. If I use the jacking point to lift the car, where do I put the jack stands so I can lower the car onto them safely?
If you have a low profile jack and pad (hockey puck) you can move 4" back from standard jacking point of the front of car or 4" forward of the rear jacking point.
You can actually from either spot lift the entire side of the car and place jack stands on the standard point on front and rear and then move to the other side and do the same thing, I have been doing it this way for the last 7 years with never an issue, just make sure you are placing a hockey puck pad on jack and using good and sturdy stands, I also am using the insert on stands that fits into the hole at the standard jacking point.
Some ideas here...
http://986forum.com/forums/general-discussions/24562-jack-stand-placements.html
...including a link in my post as to how I do mine. Mildly labor intensive initially to make the jacking block (the 4x4), but once it's done it's done. It has worked very well for me for a number of years.
To raise the front: Lift at the rear jacking point until you can get the jackstand under the front jacking point. Then do the other side the same way.
To raise the rear: Lift from the rear end under the car at the rear suspension mounting point until you can get a jackstand under the rear jacking point. Then do the other side the same way.
Are people needing hockey pucks on the stands? I use one on my jack pad. But I only have jacked up the car once for practice. I am about to do a oil change and will lift the rear of the car. I noticed my stands bracket shape didn't quite fit the stand area so well... So I would like to do something but I am not sure how I would mount a puck to the stand...
Harbor freight sells the rubber pads that fit on top of the jack stands, i got 4 for about $15. No need to use a hockey puck.
I've seen people carving out a hockey puck to fit on on their floor jack, but again, harbor freights has great aluminum floor jack that have a built in protecting pad.
Pads? We don't need no stinkin' pads!
Seriously, it is SCARRY at first but after a few times it becomes old hat.
Good to have pucks but I use a rubber.
Hey everyone...I've included a link and video to our 'QuickJack' product. I think it'll help a lot of you out with your DIY projects and general maintenance. We also carry rubber contact blocks for those of you using hockey pucks
Let us know your thoughts and as always, best of luck!
QuickJack Lifts -
Bend-Pak Lifts - PelicanParts.com
-Dmitry
I use Esco stands that have a rubber pad built in. I also have a plain hockey puck on my jack so that the claw shaped metal cup does not contact the underbody.
This would be great for brake and wheel work, but I just couldn't bring myself to get under the car with a Quikjack. But this is just old paranoid me...never totally comfortable under a car unless I have a solid set of jackstands and a couple of big blocks of wood just in case.
Froggo, could you provide more detail about these stands and how you get the car onto them?
With a regular jack, I would image you have to raise each wheel a few inches at a time, which looks like it would take ages.
Ok it's really quite quick about 20 min tops . The stands are two stage about 200mm each , so with the stand on low , jack the car using the car jacking point , [ say the front right ] so the stand can go under the front right wheel . lower the car onto it and then jack the front left side and do the same . If you want the car up level then do the rear wheels as well . the car is now 200mm higher , which may be enough for some servicing .For the next stage put the jack in as the last photo , then jack up the car and stand and slide in the pins , do all four wheels . If you want to take off a wheel say to work on the brakes , I place a jack stand under the car jack point next to that wheel and then lower the wheel jack stand and remove it .I made these stands because I cant drill my floor for a car hoist to be bolted down , the floor is hot water heated and has pipes all through it , drilling is bound to hit one .
