Rennlist

Gen 1 GT3 Side Skirt Hardware

Add to repair workspace

New repair projectOpen repair workspace

Original source

6 captured repliesDiscussion pagination complete · Source accounts, not a confirmed diagnosis

THIS DISCUSSION / SOURCE-DERIVED OVERVIEW

Discussion summary

YOUR RESEARCHGen 1 GT3 Side Skirt Hardware

Leading reported evidence

Replace factory xaa left skirt due

Performed · outcome unconfirmed

No successful repair reported for this finding.

0
Reported fixes: 0
Unsuccessful attempts: 1
Discussions

Read evidence and context

Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.

Discussions that performed work without a confirmed outcome: 1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Performed · outcome unconfirmed
I recently replaced my factory XAA left skirt due to a portable jack incident.
Original post Read captured discussion
Gen 1 GT3 Side Skirt Hardware

Read full discussion summary

Leading evidence: 'Replace factory xaa left skirt due' (no explicit attributable resolution; this is a reported action or suggestion). Across 1 matching discussions, The most frequently discussed action is 'Replace factory xaa left skirt due' (1 discussions). For that action, 0 discussions report a resolution and 0 report an unsuccessful attempt. No action has an explicit, attributable resolution report under the current rules. These are forum reports and suggestions, not a confirmed diagnosis.

Source reports, not a diagnosis or a success probability. Counts refer to discussions and can overlap.

Read captured replies

1 matching discussions · 6 captured posts examined · 0 partial discussions

Compare 1 other evidence results

Use tape

Suggestion or failed attempt

No successful repair reported for this finding.

0
Reported fixes: 0
Unsuccessful attempts: 1
Discussions

Read evidence and context

Discussions that contain suggestions: 1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Suggestion
Retaining strip on top - but I think many have opted to use tape for the upper attachment rather than screw in the retaining strip.
Original post Read captured discussion
Gen 1 GT3 Side Skirt Hardware

Frequently discussed actions (2)

These are separate views of the same evidence. Frequency alone does not establish a fix, and these counts must not be added together.

Replace factory xaa left skirt due

No successful repair reported for this finding.

0
Reported fixes: 0
Unsuccessful attempts: 1
Discussions

Read evidence and context

Discussions that performed work without a confirmed outcome: 1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Performed · outcome unconfirmed
I recently replaced my factory XAA left skirt due to a portable jack incident.
Original post Read captured discussion
Gen 1 GT3 Side Skirt Hardware

Use tape

No successful repair reported for this finding.

0
Reported fixes: 0
Unsuccessful attempts: 1
Discussions

Read evidence and context

Discussions that contain suggestions: 1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Suggestion
Retaining strip on top - but I think many have opted to use tape for the upper attachment rather than screw in the retaining strip.
Original post Read captured discussion
Gen 1 GT3 Side Skirt Hardware

Coverage and how to read this overview

Counts describe captured discussions, not unique people or a diagnosis. Author identities are not reliably stored. Exact duplicate evidence is counted once across matching discussions; one discussion counts at most once per action/state. Multiple repairs reported together remain a combination. Suggestions and failed attempts do not establish a fix. Matches cover whole discussions and can include related faults, model variants and incomplete threads.

6 eligible posts · 0 unverified posts · 1 discussions match the subject in their title or opening post.

Rennlist: 1 discussions

0 evidence records excluded for query context · 0 excluded by outcome qualification · 0 adjusted by outcome qualification.

0 acknowledgements have no verified action link; they do not establish a repair result.

Generation: 20261026T113718Z · outcome-qualification-6. Deterministic extraction; no AI model inference. How we use sources

POST 1 / ORIGINAL POSTEROriginal post

I just picked up some GT3 side skirts for a good deal and I cant seem to fin the oem hardware kit for them? Does anyone know the part nurmbers or were to get the hardware? Also I cant believe they use to charge over $1.5k for these as an option

POST 2Original post

Look like C4S or turbo side skirts to me, which are different from gt3/aerokit side skirts and won't fit narrow body 996. P/N 996504363 yields https://www.ebay.com.au/itm/355917886059

POST 3Original post

Quotes source post: 19785740

Agree. I recently replaced my factory XAA left skirt due to a portable jack incident. Did not look like those.

POST 4 / ORIGINAL POSTEROriginal post

Yup damn they are Turbo skirts.....May bad.....Well at least I can sell them

POST 5Original post

http://www.autoatlanta.com/porsche-p...section=810-05 Lists the hardware Retaining strip on top - but I think many have opted to use tape for the upper attachment rather than screw in the retaining strip. not sure if that was an official change at some point. U clamps on bottom attached the tsb instructions

POST 6Original post

The 996.2 side skirts have adhesive at the top instead of screws like the 996.1 originally had. I’m not sure about current 996.1 side skirts.

This is a source reference. Confirm exact model applicability in the original material.