Porsche Club GB

IMS Guardian install

Add to repair workspace

New repair projectOpen repair workspace

Original source

2 captured repliesDiscussion pagination complete · Source accounts, not a confirmed diagnosis

THIS DISCUSSION / SOURCE-DERIVED OVERVIEW

Discussion summary

YOUR RESEARCHIMS Guardian install

Leading reported evidence

Check couple of other switches and numer three is

Suggestion or failed attempt

No successful repair reported for this finding.

0
Reported fixes: 0
Unsuccessful attempts: 1
Discussions

Read evidence and context

Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.

Discussions that contain suggestions: 1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Suggestion · Original poster
As I've come to wire into a switch to power the IMS switch the instructions say to connect to number 3 on the switch block.There are five terminals,three in a line and two below,the installation disc shows number three as being in the lower pair but number three is on the section with three terminals.I'm taking the connection from the PSM switch as that's the nearest one and have checked a couple of other switches and numer three is on the row of three terminals on all of them,I don't want to damage anything and wondered if anyone has fitted one themselves and could confirm what I'm doing is ok.Thanks in advance for any advice.
Original post Read captured discussion
IMS Guardian install

Read full discussion summary

Leading evidence: 'Check couple of other switches and numer three is' (no explicit attributable resolution; this is a reported action or suggestion). Across 1 matching discussions, The most frequently discussed action is 'Check couple of other switches and numer three is' (1 discussions). For that action, 0 discussions report a resolution and 0 report an unsuccessful attempt. No action has an explicit, attributable resolution report under the current rules. These are forum reports and suggestions, not a confirmed diagnosis.

Source reports, not a diagnosis or a success probability. Counts refer to discussions and can overlap.

Read captured replies

1 matching discussions · 2 captured posts examined · 0 partial discussions

Frequently discussed actions (1)

These are separate views of the same evidence. Frequency alone does not establish a fix, and these counts must not be added together.

Check couple of other switches and numer three is

No successful repair reported for this finding.

0
Reported fixes: 0
Unsuccessful attempts: 1
Discussions

Read evidence and context

Discussions that contain suggestions: 1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Suggestion · Original poster
As I've come to wire into a switch to power the IMS switch the instructions say to connect to number 3 on the switch block.There are five terminals,three in a line and two below,the installation disc shows number three as being in the lower pair but number three is on the section with three terminals.I'm taking the connection from the PSM switch as that's the nearest one and have checked a couple of other switches and numer three is on the row of three terminals on all of them,I don't want to damage anything and wondered if anyone has fitted one themselves and could confirm what I'm doing is ok.Thanks in advance for any advice.
Original post Read captured discussion
IMS Guardian install

Coverage and how to read this overview

Counts describe captured discussions, not unique people or a diagnosis. Author identities are not reliably stored. Exact duplicate evidence is counted once across matching discussions; one discussion counts at most once per action/state. Multiple repairs reported together remain a combination. Suggestions and failed attempts do not establish a fix. Matches cover whole discussions and can include related faults, model variants and incomplete threads.

2 eligible posts · 0 unverified posts · 1 discussions match the subject in their title or opening post.

Porsche Club GB: 1 discussions

0 evidence records excluded for query context · 0 excluded by outcome qualification · 0 adjusted by outcome qualification.

0 acknowledgements have no verified action link; they do not establish a repair result.

Generation: 20261026T144035Z · outcome-qualification-6. Deterministic extraction; no AI model inference. How we use sources

POST 1 / ORIGINAL POSTEROriginal post

I'm fitting an IMS Guardian which I bought from a guy in the U.S. As I've come to wire into a switch to power the IMS switch the instructions say to connect to number 3 on the switch block.There are five terminals,three in a line and two below,the installation disc shows number three as being in the lower pair but number three is on the section with three terminals.I'm taking the connection from the PSM switch as that's the nearest one and have checked a couple of other switches and numer three is on the row of three terminals on all of them,I don't want to damage anything and wondered if anyone has fitted one themselves and could confirm what I'm doing is ok.Thanks in advance for any advice.

POST 2Original post

Drop me an email, and I'll send you the instructions I did for the UK kits.

This is a source reference. Confirm exact model applicability in the original material.