fullymatted.
Back to search
Pelican Parts

New Gear Shift Lever

Add to repair workspace
Open repair workspace
Original source
4 captured repliesDiscussion pagination complete · Source accounts, not a confirmed diagnosis
THIS DISCUSSION / SOURCE-DERIVED OVERVIEW

Discussion summary

YOUR RESEARCHNew Gear Shift Lever

Leading reported evidence

Replace knob

Suggestion or failed attempt

No successful repair reported for this finding.

0
Reported fixes
0
Unsuccessful attempts
1
Discussions
Read evidence and context

Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.

Discussions that contain suggestions
1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Suggestion · Original poster

I also wanted to replace the old knob, but both levers being flat meant I would have to use one of the clunky knobs made to fit.

Original post Read captured discussion
New Gear Shift Lever
Read full discussion summary

Leading evidence: 'Replace knob' (no explicit attributable resolution; this is a reported action or suggestion). Across 1 matching discussions, The most frequently discussed action is 'Replace knob' (1 discussions). For that action, 0 discussions report a resolution and 0 report an unsuccessful attempt. No action has an explicit, attributable resolution report under the current rules. These are forum reports and suggestions, not a confirmed diagnosis.

Source reports, not a diagnosis or a success probability. Counts refer to discussions and can overlap.

Read captured replies

1 matching discussions · 4 captured posts examined · 0 partial discussions

Compare 1 other evidence results

Use of a normal threaded knob

Suggestion or failed attempt

No successful repair reported for this finding.

0
Reported fixes
0
Unsuccessful attempts
1
Discussions
Read evidence and context

Explicit resolution reports before identified causes, performed actions and suggestions. Within each level, matching component labels precede direct query mentions and inherited thread context; successful versus unsuccessful discussion counts, owner confirmations and independent discussion support determine order. This is not a probability of success.

Discussions that contain suggestions
1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Suggestion · Original poster

So, I decided to make a new round shift lever that would allow the use of a normal threaded knob.

Original post Read captured discussion
New Gear Shift Lever
Frequently discussed actions (2)

These are separate views of the same evidence. Frequency alone does not establish a fix, and these counts must not be added together.

Replace knob

No successful repair reported for this finding.

0
Reported fixes
0
Unsuccessful attempts
1
Discussions
Read evidence and context
Discussions that contain suggestions
1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Suggestion · Original poster

I also wanted to replace the old knob, but both levers being flat meant I would have to use one of the clunky knobs made to fit.

Original post Read captured discussion
New Gear Shift Lever

Use of a normal threaded knob

No successful repair reported for this finding.

0
Reported fixes
0
Unsuccessful attempts
1
Discussions
Read evidence and context
Discussions that contain suggestions
1

0 original-poster resolution reports. Counts can overlap; they are not unique people or a success rate.

0 discussions have direct query context; 0 report a fix in that context. Other evidence may inherit the discussion’s subject.

Suggestion · Original poster

So, I decided to make a new round shift lever that would allow the use of a normal threaded knob.

Original post Read captured discussion
New Gear Shift Lever
Coverage and how to read this overview

Counts describe captured discussions, not unique people or a diagnosis. Author identities are not reliably stored. Exact duplicate evidence is counted once across matching discussions; one discussion counts at most once per action/state. Multiple repairs reported together remain a combination. Suggestions and failed attempts do not establish a fix. Matches cover whole discussions and can include related faults, model variants and incomplete threads.

4 eligible posts · 0 unverified posts · 1 discussions match the subject in their title or opening post.

  • Pelican Parts: 1 discussions

0 evidence records excluded for query context · 0 excluded by outcome qualification · 0 adjusted by outcome qualification.

0 acknowledgements have no verified action link; they do not establish a repair result.

Generation: 20261027T013556Z · outcome-qualification-6. Deterministic extraction; no AI model inference. How we use sources

POST 1 / ORIGINAL POSTEROriginal post

I wasn't particularly happy with the stock shift lever, so I bought one of the short shifters. I was also dissatisfied with it; mainly because of the odd angle, but it also felt a little too notchy. I also wanted to replace the old knob, but both levers being flat meant I would have to use one of the clunky knobs made to fit. So, I decided to make a new round shift lever that would allow the use of a normal threaded knob. The factory lever has about 1 inch of round before the metal is flattened so the knob slots on. I cut the flat portion off and threaded the remaining round. I then took some stainless and turned a new lever on my lathe. One end is tapped with 1/2-20 threads and is loc-tited onto the shortened shifter. The other end has a male thread that fits common 1/2-20 knobs. I had some walnut, maple, and brass, so I also made a 917-style knob. The old knob was cut from the leather boot and I made an aluminum collar that slips over the new lever. I think it turned out well. If you don't have a lathe, I think you could get similar results with off the shelf parts from McMaster Carr or the like. eBay has shift knobs of various colors and in various thread pitches with the right shift pattern for a 996. And you could make a shorter shift lever if you wanted, though mine is stock length.

POST 2Original post

Nice - I have a spare shift console which I could modify...you have me thinking now.

POST 3Original post

Let us know if you go that route jwetering! We'd love to see some pictures -Dmitry

POST 4 / ORIGINAL POSTEROriginal post

Here's the part I made and what I described above:

This is a source reference. Confirm exact model applicability in the original material.